Close
Produkter
    Filters
    Preferanser
    Søk

    Gjengetapper

    Se som Grid Liste
    Sorter etter
    Vis per side

    Tap, Metric, M.5-.90

    Varenummer T509M

    Tap, Metric, M10-1.25

    Varenummer T1012M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, Metric, M10-1.50

    Varenummer T1015M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, Metric, M12-1.50

    Varenummer T1215M

    Tap, Metric, M12-1.75

    Varenummer T1217M

    Tap, Metric, M3-.50

    Varenummer T305M

    Tap, Metric, M4-.70

    Varenummer T407M

    Tap, Metric, M4-.75

    Varenummer T4075M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, Metric, M5-.80

    Varenummer T508M

    Tap, Metric, M6-1.00

    Varenummer T610M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, Metric, M8-1.00

    Varenummer T810M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, Metric, M8-1.25

    Varenummer T812M

    ØAdditional Description: An important feature of the dies in these sets (except GA541 and GAM540) is a small adjusting screw which changes the nominal size .003" under or over to give a tight or loose fit to your thread. Die size 1/4" to 1/2" and 7 mm to 12 mm are a one-piece, 12-point design that can be turned with a 1" socket wrench (5/8" socket wrench for 3 to 6 mm dies) when working in places where a normal die stock cannot be used. The three largest die stocks (TD10A, TD35, and TD40) are self-centering and adjust to the diameter of the bolt. U.S. Fed. Spec. GGG-T-60 applies to taps; GGG-D-296B applies to dies. �

    Tap, NC, 3/8'-16

    Varenummer T102

    Tap, NF, 7/8'-14

    Varenummer T128

    Tap, NPT, 1/8'-27

    Varenummer T110

    Gjengetapper